Your pallet.

Your cart is empty

Subtotal, AUD

0.00 $

Safe and Easy Payments

Payments by Stripe
Payments by Polypay

Gather Co Texture Guide

Here at Gather Co we want to ensure that the gap between your screen and our surfaces is bridged. As such, we have developed this Texture Guide to provide a general understanding of the finishes across our collection and to offer a sense of the ‘feel’ you can expect from each variety.

*Please note: This is intended as a guide only. Some surfaces may sit outside the prescribed finish as stated below. It is not a Slip Rating, you’ll find that in the “Resources and Installation” section at the bottom of each product page.

Smooth
Mild
Coarse
1
2
3
4
5
Rating
Type of Finish
1
Polished A mirror-like shine accomplished by using progressively finer grit during the polishing process.
2
Brushed Brush finishing involves exposing stone surfaces to a rotating wire brush, simulating natural wear over time.
2
Honed A honed finish is achieved by applying a polishing head with a coarse grit fitting.
2
Sawn After initial cutting, the stone is lightly polished to remove the heaviest saw marks but, not enough to achieve a fully honed finish.
3
Acid Washed Acid washing is an exfoliation process where a chemical reaction is used to flake away at the stone’s surface.
3
Flamed A flamed finish is achieved through heating the surface of stone to extreme temperatures, followed by a rapid cooling process – leaving a textured, unrefined consistency.
3
Sand Blasted Sand blasting is the process of forcibly propelling streams of course material against a stone surface to smoothen or roughen it.
4
Chisseled A chiselled finish is achieved when metal combs are run over stone to form a unified grooved surface.
4
Natural A natural finish refers to stone in its raw state. It is reached through a combination of various geological conditions and prolonged environmental/atmospheric exposure.
1,2,3,4
Tumbled Tumbling is a secondary process applied in addition to one of the primary finishes. It is used to alter the edge detail of stone and typically results in reduced surface coarseness. Most commonly, tumbling is achieved by combining both stone pieces and aggregate inside a rotating rubber lined.
5
Bush Hammered This process employs either simple hand-held hammers or large electric implements. The method works through repeated surface impacts with a large metal slug made up of uniformed conical points.
5
Convict Picked A traditional stone treatment historically undertaken by convicts in Australia where steel crafting tools are repeatedly struck against the stone surface to achieve a moderate to heavily textured finish.
5
Split Splitting is achieved by mechanically or hand fragmenting stone, exposing a natural cleft and heavily textured finish.

Gather Co Rating Guide

Gather Co specialises in trading repurposed and antique fixtures. The matured nature of these genuine artifacts means that every piece comes in a distinct condition. We’ve developed this rating guide to help you quickly assess the level of wear associated with each selection.

Low
Good
High
Rating
One Star
These pieces are beautiful although their application must be carefully considered. Structural integrity is compromised.
Two Star
Likely presence of both structural faults and obvious superficial blemishes. Repairs evident.
Three Star
Minor structural issues and/or noticeable levels of wear.
Four Star
Firm structural integrity. Moderate signs of wear.
Five Star
Signs of wear still evident but, well preserved. Structurally sound.
tag tag tag tag
Gather Co. - BAIBIAN
Gather Co. - BAIBIAN Gather Co. - BAIBIAN Gather Co. - BAIBIAN

#GATHERCOGOODS

@GATHERCOAUSTRALIA

BAIBIAN

Reclaimed Cobblestones

Texture Guide: 2

Request Custom Size
$5.00 each
Add Sample

Lead Time: 2-6 Weeks

This time frame is a guide only and subject to change.
More Information

Bursting with unbridled character, our collection of reclaimed Victorian Bluestone cobblestones have been salvaged from the historical Melbourne cityscape and lovingly prepared for a new chapter.

Domestic Bluestone applied across Victorian architecture, dates back to the early 1850s when production of these cobblestones first begun. Originally split entirely by hand at roughly 300x200x150mm, these relics are synonymous with Melbourne’s bustling laneways and vibrant streets.

We’ve carefully aligned these cobblestones with modern trends and hand-cut each piece to a consistent 20mm thickness. This practice maintains a level of genuine authenticity whilst allowing for efficiency during re-installation. 

Request SAMPLES

for your projects

Add Sample

More Information

Origin

Melbourne - If we think of the bluestone in Melbourne, we may first think of the famous cobbled laneways intersecting the urban grid. Initially, these laneways were used for the collection of night soil – human excrement collected at night from buckets or privies – and they are still useful routes for collecting rubbish and recycling bins. But laneways are increasingly being reclaimed as lively strips for cafes, bars, restaurants and galleries in the city, or re-made as gardens in the suburbs.

Material

Bluestone - is not one particular stone, but in fact a commercial term used to describe a product that is commonly made up of various types of stone. In Australia various states use different names for ‘Bluestone’. For example, in Victoria Bluestone is known as Basalt. Despite naming conventions all Bluestones are hardy and commonly used for construction and foundation.